Plumbing Basics: What You Need for Bathtub Installation

Go Company

 

Just how do you actually feel in relation to Tools You Need to Install a New Bathtub ?


Installing A Bathtub
Installing a bath tub isn't precisely brain surgery, but it does call for strong plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging project. If the old bathtub is conveniently available, the job can relocate immediately; if you need to open a wall surface to remove the old tub and also position the new bath tub, the task is much harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need an assistant to move out the old bathtub as well as set in the new one. Make sure you have actually certified on your own for the task and are comfortable trying it. As opposed to working with a specialist to take over a halfway-completed job, it is much better to think about using one before you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will certainly help you set up a new bath tub in your restroom if you have actually currently gotten a new bathtub and also do not need to change the arrangement of your previous water system pipelines.
Your devices and material checklist need to make up the following:

 

  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  •  

Getting ready for the Setup


First of all, the sustaining framework provided with the bath ought to be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to avoid pressure on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last placement.

 

 

Removing Old Touches


If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be fairly problematic because of the limited accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming during this process. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
Before carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Installing the Tub


Making use of the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the tub up until the level checks out level.
To install taps, fit the bottom of the outermost versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water and also inspect all joints and new pipework for leakages as well as tighten them if required. Load the tub and also inspect the overflow outlet and also the typical electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub should wait until the bathtub has actually been used at least once as this will certainly settle it right into its last position.

 

 

Suitable New Touches


If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Safeguard the tap in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous kind should be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bath tub


In the area where the bathroom fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split an inflexible seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, leading to issues with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealant can crack fairly early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant sticky and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.


But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.


This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.


The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.


Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.


Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.


If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.


Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.


If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.


If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

 

Do you enjoy more info about Tools You Need to Install a New Bathtub ? Try to leave a remark directly below. We will be pleased to see your reactions about this post. In hopes that you visit us again in the future. Enjoyed our content? Please share it. Let other people find it. I praise you for your time. Please pay a visit to our site back soon.


Trust our expertise.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Plumbing Basics: What You Need for Bathtub Installation”

Leave a Reply

Gravatar